Update Cisco 300-135 TSHOOT questions answers pdf

Passtcert be able to help you pass Cisco certification 300-135 exam successfully.Passtcert senior experts have developed Cisco 300-135 TSHOOT questions answers pdf with their knowledge and experience, which have 95% similarity with the real exam. I believe that you will be very confident of our products. If you choose to use Passtcert Cisco 300-135 TSHOOT questions answers pdf, Passtcert can help you 100% pass your first time to attend Cisco certification 300-135 exam.

Share some CCNP 300-135 exam questions and answers below.
What is the solution of the fault condition? 
A. Under the BGP process,enter the bgp redistribute-internal command 
B. Under the BGP process, bgp confederation identifier 65001 command 
C. Delete the current BGP process and reenter all of the commands using 65002 as theAS number. 
D. Under the BGP process, delete the neighbor 209.56.200.226 remote-as 65002 command enter the neighbor 209.65.200.226 remote-as 65002 command. 
Answer: D 

Ticket 5 R1ACL 

TROUBLE TICKET STATEMENT: 
The implementation group has been using thetest bed to do a ¡®proof-of-concept¡¯that required both client 1 and client 2 to access the Web Server at 209.65.200.241.After several changed to interface status, network addressing, routing schemes and layer 2 connectivity, at trouble ticket has been opened indicating that client 1 cannot ping the 209.65.200.241 (internet Server). 
show run by yourself to obtain the following information: 
Client 1 is not able to reach the WebServer at 209.65.200.241. Initial troubleshooting shows that R1 is also not able to reach the WebServer. R1 also does not have any active BGP neighbor. 
Configuration on R1 
! interface Serial0/0/0/1 
description link to ISP 
ip address 209.65.200.224 255.255.255.252 
ip access-group edge_security in 
ip nat outside 
ip virtual-reassembly 
ntp brasdcast client 
net broadcast key 1 
no cdp enable 
!! ip access-list nat_traffic permit 10.1.0.0 0.0.255.255 
ip access-list nat_traffic permit 10.2.0.0 0.0.255.255 
! ip access-list edge_security deny ip 10.0.0.0 0.255.255.255 any 
ip access-list edge_security deny ip 172.16.0.0 0.15.255.255 any 
ip access-list edge_security deny ip 192.168.0.0 0.0.255.255 any 
ip access-list edge_security deny ip 127.0.0.0 0.255.255.255 any 
ip access-list edge_security permit ip host 209.65.200.241 any 

On which device is the fault condition located? 
A. R1 
B. R2 
C. R3 
D. R4 
E. DSW1 
F. DSW2 
G. ASW1 
Answer: A 

What is the solution of the fault condition? 
A. Under the interface Serial0/0/0 configuration enter the ip nat inside command 
B. Under the interface Serial0/0/1 configuration enter the ip nat outside command 
C. Under the ip access-list standar nat_trafic configuration enter the permit 10.2.0.0 0.0.255.255 command 
D. Under the ip access-list standar nat_trafic configuration enter the permit 209.65.200.0 0.0.0.255 command 
Answer: C

The fault condition is related to which technology? 
A. NTP 
B. IPv4 OSPF Routing 
C. IPv6 OSPF Routing 
D. IPV4 and IPV6 Interoperability 
E. IPv4 layer 3 security 
Answer: D

What is the solution to the fault condition? 
A. Under the interface Tunnel34 configuration delete the tunnel mode ipv6 command. 
B. Under the interface Serial0/0/0.34 configuration enter the ipv6 address 2026::34:1/122 command. 
C. Under the interface Tunnel34 configuration enter the ip address unnumbered Serial0/0/0.34 command. 
D. Under the interface Tunnel34 configuration delete the tunnel source Serial0/0/0.34 command and enter the tunnel source 2026::34:1/122 command. 
Answer: A

R1 and R2 OSPF neighbor. 
Which two statements are true? (Choose two) 
(Output from show ip ospf neighbors on 2 routers, one of them shows FULL/DR, the other FULL/-, you need to know how were they configured and will they exchange routes) 
A. They are not neighbors 
B. R1 (non-DR) will not update its routes to R2 
C. Router R2 is configured with ospf point-to-point command (R2 is the router that shows as FULL/-) 
D. They need to be configured as OSPF NBMA 
E. R2 should be configured as stub 
Answer: BC

The Fault Condition is related to which technology? 
A. BGP 
B. NTP 
C. IP NAT 
D. IPv4 OSPF Routing 
E. IPv4 OSPF Redistribution 
F. IPv6 OSPF Routing 
G. IPv4 layer 3 security 
Answer: A

What is the solution to the fault condition? 
A. Under the interface Tunnel34 configuration enter the ipv6 ospf 6 area 34 command. 
B. Under the interface Loopback6 configuration enter the ipv6 ospf 6 area 34 command. 
C. Under the interface Serial0/0/0.34 configuration enter the ipv6 ospf 6 area 34 command. 
D. Under ipv6 router ospf 6 configuration enter the redistribute rip RIP_ZONE include-connected command. 
Answer: D

What is the MTU¡¯s size in a GRE tunnel? 
A. 1630 
B. 1476 
C. 1500 
D. 1900 
Answer: B

Nowadays in this talented society IT professionals are very popular, but the IT area are also very competitive. So many IT professionals through passing difficult IT certification exams to stabilize themselves. Passtcert is websites specifically provide convenience for candidates participating in the IT certification exams.Passtcert is a website to provide Cisco 300-135 TSHOOT questions answers pdf for people who attend IT certification exam examinee.

Never say you can not do it. This is my advice to everyone. Even if you think that you can not pass the demanding Cisco 300-135 exam. You can find a quick and convenient training tool to help you. Passtcert Cisco 300-135 TSHOOT questions answers pdf is a very good training materials. It can help you to pass the exam successfully. And its price is very reasonable, you will benefit from it. Quickly grab your hope, it is in the Passtcert Cisco 300-135 TSHOOT questions answers pdf.

Related article: http://h13-531.blogspot.com/2017/09/update-cisco-ccnp-300-135-tshoot.html